--- /dev/null
+#ifndef PINS_H_INCLUDED
+#define PINS_H_INCLUDED
+
+// Detects if we are on USB power.
+#define VBUS_DET GPIO(GPIO_PORTA, 3)
+
+// Buttons
+#define BTN_ALARM GPIO(GPIO_PORTA, 2)
+#define WATCH_BTN_ALARM_EIC_CHANNEL 2
+#define BTN_LIGHT GPIO(GPIO_PORTB, 5)
+#define WATCH_BTN_LIGHT_EIC_CHANNEL 5
+#define BTN_MODE GPIO(GPIO_PORTA, 7)
+#define WATCH_BTN_MODE_EIC_CHANNEL 7
+
+// Buzzer
+#define BUZZER GPIO(GPIO_PORTA, 27)
+#define WATCH_BUZZER_TCC_PINMUX PINMUX_PA27F_TCC0_WO5
+#define WATCH_BUZZER_TCC_CHANNEL 1
+
+// LEDs
+#define WATCH_INVERT_LED_POLARITY
+#define RED GPIO(GPIO_PORTA, 4)
+#define WATCH_RED_TCC_CHANNEL 0
+#define WATCH_RED_TCC_PINMUX PINMUX_PA04E_TCC0_WO0
+
+#ifdef WATCH_SWAP_LED_PINS
+ #define GREEN GPIO(GPIO_PORTB, 22)
+ #define WATCH_GREEN_TCC_CHANNEL 2
+ #define WATCH_GREEN_TCC_PINMUX PINMUX_PB22F_TCC0_WO2
+#else
+ #define GREEN GPIO(GPIO_PORTB, 23)
+ #define WATCH_GREEN_TCC_CHANNEL 3
+ #define WATCH_GREEN_TCC_PINMUX PINMUX_PB23F_TCC0_WO3
+#endif
+
+
+// Segment LCD
+#define SLCD0 GPIO(GPIO_PORTB, 6)
+#define SLCD1 GPIO(GPIO_PORTB, 7)
+#define SLCD2 GPIO(GPIO_PORTB, 8)
+#define SLCD3 GPIO(GPIO_PORTB, 9)
+#define SLCD4 GPIO(GPIO_PORTA, 5)
+#define SLCD5 GPIO(GPIO_PORTA, 6)
+#define SLCD6 GPIO(GPIO_PORTA, 8)
+#define SLCD7 GPIO(GPIO_PORTA, 9)
+#define SLCD8 GPIO(GPIO_PORTA, 10)
+#define SLCD9 GPIO(GPIO_PORTA, 11)
+#define SLCD10 GPIO(GPIO_PORTB, 11)
+#define SLCD11 GPIO(GPIO_PORTB, 12)
+#define SLCD12 GPIO(GPIO_PORTB, 13)
+#define SLCD13 GPIO(GPIO_PORTB, 14)
+#define SLCD14 GPIO(GPIO_PORTB, 15)
+#define SLCD15 GPIO(GPIO_PORTA, 14)
+#define SLCD16 GPIO(GPIO_PORTA, 15)
+#define SLCD17 GPIO(GPIO_PORTA, 16)
+#define SLCD18 GPIO(GPIO_PORTA, 17)
+#define SLCD19 GPIO(GPIO_PORTA, 18)
+#define SLCD20 GPIO(GPIO_PORTA, 19)
+#define SLCD21 GPIO(GPIO_PORTB, 16)
+#define SLCD22 GPIO(GPIO_PORTB, 17)
+#define SLCD23 GPIO(GPIO_PORTA, 20)
+#define SLCD24 GPIO(GPIO_PORTA, 21)
+#define SLCD25 GPIO(GPIO_PORTA, 22)
+#define SLCD26 GPIO(GPIO_PORTA, 23)
+// This board uses a slightly different pin mapping from the standard watch, and it's not enough to
+// just declare the pins. We also have to set the LCD Pin Enable register with the SLCD pins we're
+// using. These numbers are not port/pin numbers, but the "SLCD/LP[x]" numbers in the pinmux table.
+// If not defined in pins.h, the LCD drover will fall back to the pin mapping in hpl_slcd_config.h.
+// LPENL is for pins SLCD/LP[0..31].
+#define CONF_SLCD_LPENL (\
+ (uint32_t)1 << 0 | \
+ (uint32_t)1 << 1 | \
+ (uint32_t)1 << 2 | \
+ (uint32_t)1 << 3 | \
+ (uint32_t)1 << 5 | \
+ (uint32_t)1 << 6 | \
+ (uint32_t)1 << 11 | \
+ (uint32_t)1 << 12 | \
+ (uint32_t)1 << 13 | \
+ (uint32_t)1 << 14 | \
+ (uint32_t)1 << 21 | \
+ (uint32_t)1 << 22 | \
+ (uint32_t)1 << 23 | \
+ (uint32_t)1 << 24 | \
+ (uint32_t)1 << 25 | \
+ (uint32_t)1 << 30 | \
+ (uint32_t)1 << 31 | 0)
+// LPENH is for pins SLCD/LP[32..51], where bit 0 represents pin 32.
+#define CONF_SLCD_LPENH (\
+ (uint32_t)1 << (32 - 32) | \
+ (uint32_t)1 << (33 - 32) | \
+ (uint32_t)1 << (34 - 32) | \
+ (uint32_t)1 << (35 - 32) | \
+ (uint32_t)1 << (42 - 32) | \
+ (uint32_t)1 << (43 - 32) | \
+ (uint32_t)1 << (48 - 32) | \
+ (uint32_t)1 << (49 - 32) | \
+ (uint32_t)1 << (50 - 32) | \
+ (uint32_t)1 << (51 - 32) | 0)
+
+
+// 9-pin connector
+#define A0 GPIO(GPIO_PORTB, 4)
+#define WATCH_A0_EIC_CHANNEL 4
+#define A1 GPIO(GPIO_PORTB, 1)
+#define WATCH_A1_EIC_CHANNEL 1
+#define A2 GPIO(GPIO_PORTB, 2)
+#define WATCH_A2_EIC_CHANNEL 2
+#define A3 GPIO(GPIO_PORTB, 3)
+#define WATCH_A3_EIC_CHANNEL 3
+#define A4 GPIO(GPIO_PORTB, 0)
+#define WATCH_A4_EIC_CHANNEL 0
+#define SDA GPIO(GPIO_PORTB, 30)
+#define SCL GPIO(GPIO_PORTB, 31)
+
+// aliases for as A3/A4; these were mentioned as D0/D1 in early documentation.
+#define D0 GPIO(GPIO_PORTB, 3)
+#define D1 GPIO(GPIO_PORTB, 0)
+
+#endif // PINS_H_INCLUDED
+++ /dev/null
-#ifndef PINS_H_INCLUDED
-#define PINS_H_INCLUDED
-
-// Detects if we are on USB power.
-#define VBUS_DET GPIO(GPIO_PORTA, 3)
-
-// Buttons
-#define BTN_ALARM GPIO(GPIO_PORTA, 2)
-#define WATCH_BTN_ALARM_EIC_CHANNEL 2
-#define BTN_LIGHT GPIO(GPIO_PORTB, 5)
-#define WATCH_BTN_LIGHT_EIC_CHANNEL 5
-#define BTN_MODE GPIO(GPIO_PORTA, 7)
-#define WATCH_BTN_MODE_EIC_CHANNEL 7
-
-// Buzzer
-#define BUZZER GPIO(GPIO_PORTA, 27)
-#define WATCH_BUZZER_TCC_PINMUX PINMUX_PA27F_TCC0_WO5
-#define WATCH_BUZZER_TCC_CHANNEL 1
-
-// LEDs
-#define WATCH_INVERT_LED_POLARITY
-#define RED GPIO(GPIO_PORTB, 22)
-#define WATCH_RED_TCC_PINMUX PINMUX_PB22F_TCC0_WO2
-#define WATCH_RED_TCC_CHANNEL 2
-
-#ifdef WATCH_SWAP_LED_PINS
- #define GREEN GPIO(GPIO_PORTA, 4)
- #define WATCH_GREEN_TCC_CHANNEL 0
- #define WATCH_GREEN_TCC_PINMUX PINMUX_PA04E_TCC0_WO0
-#else
- #define GREEN GPIO(GPIO_PORTB, 23)
- #define WATCH_GREEN_TCC_CHANNEL 3
- #define WATCH_GREEN_TCC_PINMUX PINMUX_PB23F_TCC0_WO3
-#endif
-
-
-// Segment LCD
-#define SLCD0 GPIO(GPIO_PORTB, 6)
-#define SLCD1 GPIO(GPIO_PORTB, 7)
-#define SLCD2 GPIO(GPIO_PORTB, 8)
-#define SLCD3 GPIO(GPIO_PORTB, 9)
-#define SLCD4 GPIO(GPIO_PORTA, 5)
-#define SLCD5 GPIO(GPIO_PORTA, 6)
-#define SLCD6 GPIO(GPIO_PORTA, 8)
-#define SLCD7 GPIO(GPIO_PORTA, 9)
-#define SLCD8 GPIO(GPIO_PORTA, 10)
-#define SLCD9 GPIO(GPIO_PORTA, 11)
-#define SLCD10 GPIO(GPIO_PORTB, 11)
-#define SLCD11 GPIO(GPIO_PORTB, 12)
-#define SLCD12 GPIO(GPIO_PORTB, 13)
-#define SLCD13 GPIO(GPIO_PORTB, 14)
-#define SLCD14 GPIO(GPIO_PORTB, 15)
-#define SLCD15 GPIO(GPIO_PORTA, 14)
-#define SLCD16 GPIO(GPIO_PORTA, 15)
-#define SLCD17 GPIO(GPIO_PORTA, 16)
-#define SLCD18 GPIO(GPIO_PORTA, 17)
-#define SLCD19 GPIO(GPIO_PORTA, 18)
-#define SLCD20 GPIO(GPIO_PORTA, 19)
-#define SLCD21 GPIO(GPIO_PORTB, 16)
-#define SLCD22 GPIO(GPIO_PORTB, 17)
-#define SLCD23 GPIO(GPIO_PORTA, 20)
-#define SLCD24 GPIO(GPIO_PORTA, 21)
-#define SLCD25 GPIO(GPIO_PORTA, 22)
-#define SLCD26 GPIO(GPIO_PORTA, 23)
-// This board uses a slightly different pin mapping from the standard watch, and it's not enough to
-// just declare the pins. We also have to set the LCD Pin Enable register with the SLCD pins we're
-// using. These numbers are not port/pin numbers, but the "SLCD/LP[x]" numbers in the pinmux table.
-// If not defined in pins.h, the LCD drover will fall back to the pin mapping in hpl_slcd_config.h.
-// LPENL is for pins SLCD/LP[0..31].
-#define CONF_SLCD_LPENL (\
- (uint32_t)1 << 0 | \
- (uint32_t)1 << 1 | \
- (uint32_t)1 << 2 | \
- (uint32_t)1 << 3 | \
- (uint32_t)1 << 5 | \
- (uint32_t)1 << 6 | \
- (uint32_t)1 << 11 | \
- (uint32_t)1 << 12 | \
- (uint32_t)1 << 13 | \
- (uint32_t)1 << 14 | \
- (uint32_t)1 << 21 | \
- (uint32_t)1 << 22 | \
- (uint32_t)1 << 23 | \
- (uint32_t)1 << 24 | \
- (uint32_t)1 << 25 | \
- (uint32_t)1 << 30 | \
- (uint32_t)1 << 31 | 0)
-// LPENH is for pins SLCD/LP[32..51], where bit 0 represents pin 32.
-#define CONF_SLCD_LPENH (\
- (uint32_t)1 << (32 - 32) | \
- (uint32_t)1 << (33 - 32) | \
- (uint32_t)1 << (34 - 32) | \
- (uint32_t)1 << (35 - 32) | \
- (uint32_t)1 << (42 - 32) | \
- (uint32_t)1 << (43 - 32) | \
- (uint32_t)1 << (48 - 32) | \
- (uint32_t)1 << (49 - 32) | \
- (uint32_t)1 << (50 - 32) | \
- (uint32_t)1 << (51 - 32) | 0)
-
-
-// 9-pin connector
-#define A0 GPIO(GPIO_PORTB, 4)
-#define WATCH_A0_EIC_CHANNEL 4
-#define A1 GPIO(GPIO_PORTB, 1)
-#define WATCH_A1_EIC_CHANNEL 1
-#define A2 GPIO(GPIO_PORTB, 2)
-#define WATCH_A2_EIC_CHANNEL 2
-#define A3 GPIO(GPIO_PORTB, 3)
-#define WATCH_A3_EIC_CHANNEL 3
-#define A4 GPIO(GPIO_PORTB, 0)
-#define WATCH_A4_EIC_CHANNEL 0
-#define SDA GPIO(GPIO_PORTB, 30)
-#define SCL GPIO(GPIO_PORTB, 31)
-
-// aliases for as A3/A4; these were mentioned as D0/D1 in early documentation.
-#define D0 GPIO(GPIO_PORTB, 3)
-#define D1 GPIO(GPIO_PORTB, 0)
-
-#endif // PINS_H_INCLUDED
ifeq ($(LED), BLUE)
CFLAGS += -DWATCH_SWAP_LED_PINS
endif
+
+ifeq ($(BOARD), OSO-FEAL-A1-00)
+CFLAGS += -DCRYSTALLESS
+endif
// <i> Indicates whether the external interrupt 5 filter is enabled or not
// <id> eic_arch_filten5
#ifndef CONF_EIC_FILTEN5
-#define CONF_EIC_FILTEN5 0
+#define CONF_EIC_FILTEN5 1
#endif
// <q> External Interrupt 5 Event Output Enable
// </e>
+// my god this is a hack. need to refactor this out of ASF and into our driver. - joey 10/19
+#ifdef CRYSTALLESS
+#define CONFIG_EIC_EXTINT_MAP {2, PIN_PA02}, {5, PIN_PB05}, {7, PIN_PA07},
+#else
#define CONFIG_EIC_EXTINT_MAP {2, PIN_PA02}, {6, PIN_PA22}, {7, PIN_PA23},
+#endif
// <<< end of configuration section >>>
// <i> This defines the clock source for generic clock generator 3
// <id> gclk_gen_3_oscillator
#ifndef CONF_GCLK_GEN_3_SOURCE
+#ifdef CRYSTALLESS
+#define CONF_GCLK_GEN_3_SOURCE GCLK_GENCTRL_SRC_OSCULP32K
+#else
#define CONF_GCLK_GEN_3_SOURCE GCLK_GENCTRL_SRC_XOSC32K
#endif
+#endif
+
// <q> Run in Standby
// <i> Indicates whether Run in Standby is enabled or not
// <id> gclk_arch_gen_3_runstdby
// <i> This defines the clock source for RTC
// <id> rtc_source_oscillator
#ifndef CONF_RTCCTRL_SRC
+#ifdef CRYSTALLESS
+#define CONF_RTCCTRL_SRC GCLK_GENCTRL_SRC_OSCULP32K
+#else
#define CONF_RTCCTRL_SRC GCLK_GENCTRL_SRC_XOSC32K
#endif
+#endif
// <q> Use 1 kHz output
// <id> rtc_1khz_selection
sense_pos = 4 * (WATCH_A4_EIC_CHANNEL % 8);
break;
case BTN_ALARM:
- // for the buttons, we need an internal pull-down.
- gpio_set_pin_pull_mode(pin, GPIO_PULL_DOWN);
config_index = (WATCH_BTN_ALARM_EIC_CHANNEL > 7) ? 1 : 0;
sense_pos = 4 * (WATCH_BTN_ALARM_EIC_CHANNEL % 8);
break;
case BTN_LIGHT:
- gpio_set_pin_pull_mode(pin, GPIO_PULL_DOWN);
config_index = (WATCH_BTN_LIGHT_EIC_CHANNEL > 7) ? 1 : 0;
sense_pos = 4 * (WATCH_BTN_LIGHT_EIC_CHANNEL % 8);
break;
case BTN_MODE:
- gpio_set_pin_pull_mode(pin, GPIO_PULL_DOWN);
config_index = (WATCH_BTN_MODE_EIC_CHANNEL > 7) ? 1 : 0;
sense_pos = 4 * (WATCH_BTN_MODE_EIC_CHANNEL % 8);
break;
}
gpio_set_pin_direction(pin, GPIO_DIRECTION_IN);
- gpio_set_pin_function(pin, GPIO_PIN_FUNCTION_A);
// EIC configuration register is enable-protected, so we have to disable it first...
if (hri_eic_get_CTRLA_reg(EIC, EIC_CTRLA_ENABLE)) {
config &= ~(7 << sense_pos);
config |= trigger << (sense_pos);
hri_eic_write_CONFIG_reg(EIC, config_index, config);
+ // ...set the pin mode...
+ gpio_set_pin_function(pin, GPIO_PIN_FUNCTION_A);
+ if (pin == BTN_ALARM || pin == BTN_LIGHT || pin == BTN_MODE) gpio_set_pin_pull_mode(pin, GPIO_PULL_DOWN);
// ...and re-enable the EIC
hri_eic_set_CTRLA_ENABLE_bit(EIC);
projects / sensor-watch.git / commitdiff